DGS 1216T MANUAL PDF

Page 5: About This Guide Reproduction in any manner whatsoever without the written permission of D-Link Corporation is strictly forbidden. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Step1: Unpacking Open the shipping carton and carefully unpack its contents. Please consult the packing list located in the User Manual to make sure all items are present and undamaged. Figure 3 — Mount the Switch in the rack or chassis Step 3 — Plugging in the AC Power Cord Users may now connect the AC power cord into the rear of the switch and to an electrical outlet preferably one that is grounded and surge protected. Page 8: Getting Started Switch.

Author:Nashura Yozshut
Country:Kazakhstan
Language:English (Spanish)
Genre:Software
Published (Last):25 January 2017
Pages:319
PDF File Size:9.58 Mb
ePub File Size:6.70 Mb
ISBN:632-4-30311-945-7
Downloads:99170
Price:Free* [*Free Regsitration Required]
Uploader:Moran



Page 3 Setup Menu Switching is a cost-effective way of increasing the total network capacity available to users on a local area network. A switch increases capacity and decreases network loading by dividing a local area network into different segments, which do not compete with each other for network transmission capacity. Page 9: Unpacking And Installation This chapter provides unpacking and installation information for the Switch. Unpacking Open the shipping carton of the Switch and carefully unpacks its contents.

Page Rack Mounting Figure 1. Attach the adhesive rubber pads to the bottom. Rack Mounting The Switch can be mounted in an EIA standard-size, inch rack, which can be placed in a wiring closet with other equipment.

The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan. Front Panel The figure below shows the front panels of the Switch. Figure 4.

Front panel of port Gigabit Ethernet Switch. Rear panel of the Switch. AC Power Connector: This is a three-pronged connector that supports the power cord. Plug in the female connector of the provided power cord into this connector, and the male into a power outlet.

Supported input voltages range from V AC at Hz. Page Understanding Led Indicators Figure 6. LED indicators of the Switch. With the included Web Management Utility, you can easily discover all the Web Managed switches, assign IP Addresses, change passwords and upgrade new firmware. For detailed explanation, follow the section below. Discovery List This is the list where you can discover all the Web management devices in the entire network. Page 18 Gateway: Shows the Gateway set of the device.

When the indicator lights green, it means that there is no trap transmitted. Page Device Setting Figure 9. Page 20 Figure Configuration Setting Password Change: To change the password, enter the original password, the new password, and confirm the original password.

Figure Password Change Firmware Upgrade: When the device has a new function, there will be a new firmware to update the device. It will show the current version of the Web Management Utility. The Switch can be configured through the Web Browser.

A network administrator can manage, control, and monitor the Switch from the local area network. When the following dialog page appears, enter the default password "admin" Click on the setup item that you want to configure. Page 25 The Link Status in the screen will show the connection speed and duplex mode. If the port is disconnected, the dialog box will display down.

Flow Control: This setting determines whether or not the Switch will be handling flow control. Set FlowCtrl to Enable to avoid data transfer overflows. The new VLAN configuration window will appear. It enables the manager to keep close track of switch performance and alter it if necessary.

Page System Setting Figure Statistic For detailed packet information, click on the ID parameter as shown in Figure Page Trap Setting Figure Set the Trap IP Address of the manager where the trap will be sent. Device Bootup: A trap when booting up the system. Set Password Backup Setting The backup tools help you to backup the current switch settings. Page Reset Setting Figure Backup Setting Note: When restoring a recorded file, the current password will not be erased.

Reset Setting The Factory Reset button helps you to reset the device back to the factory default settings. Be aware that the entire configuration will be reset. Page 36 D-Link Systems, Mt. D- Link will not be held responsible for any packages that are lost in transit to D-Link. The repaired or replaced packages will be shipped to the customer via UPS Ground or any common carrier selected by D-Link, with shipping charges prepaid.

Page 37 D-Link; Products that have been purchased from inventory clearance or liquidation sales or other sales in which D-Link, the sellers, or the liquidators expressly disclaim their warranty obligation pertaining to the product.

Contents are subject to change without prior notice. Page 39 Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights.

COMPENDIO DE NORMAS LEGALES SOBRE SALUD OCUPACIONAL ARSEG PDF

D-Link DGS-1216T - Switch Product Manual

.

AD7541 DATASHEET PDF

D-Link DGS-1216T User Manual

.

MICROCOSMOGRAPHIA ACADEMICA PDF

D-link DGS-1216T User Manual

.

Related Articles